OpenWrt su Pirelli STB

JackTheVendicator
Messaggi: 43
Iscritto il: sabato 22 gennaio 2011, 22:56

OpenWrt su Pirelli STB

Messaggioda JackTheVendicator » lunedì 28 novembre 2011, 13:44

Se qualcuno di voi ha sempre voluto usare l'STB come server/nodo di rete ma e' stato dissuaso dall'incasinamento del fw azbox, si faccia avanti! Mi servono developer e tester!

ATTENZIONE: Questo firmware richiede la mod per porte USB sempre attive che ho descritto qui (http://www.ilpuntotecnicoeadsl.com/foru ... #msg109457) .

Cose testate finora:
* USB e relativo boot da pendrive (entrambe le porte funzionano in modalita' 2.0!)
* ethernet
* supporto wifi con pennina USB

Cose gia' implementate ma da testare:
* supporto convertitori USB-seriale (FTDI e PL2303)
* gestione della flash interna (da effettuare con molta attenzione perche' basta un flash sbagliato e l'STB e' andato)

Cose da implementare:
* supporto smartcard
* uscite A/V (il codice e' gia' nel tree, ma non compila; inoltre il mio STB ha gli ucodes incasinati e non posso provare)

Cose che non funzionano e probabilmente non funzioneranno mai:
* LED, pulsantiera frontale, telecomando (il metodo usato dalla Pirelli non e' standard Sigma ma e' costruito ad-hoc)
* tuner

Log del boot:

{syntaxhighlighter brush: plain;fontsize: 100; first-line: 1; }********************************** * SMP863x zboot start ... * Version: 2.0.0-2.7.112.1 * Started at 0x91000000. * Configurations (chip revision: 4): * Use 8KB DRAM as stack. * Support XLoad format. * Enabled BIST mode. * Enabled memory test mode. * PIRELLI-STB based on v.2.7.120.0 DDC-20060519). ********************************** Boot from flash (0x48000000) mapped to 0xac000000. Found XENV block at 0xac000000. CPU clock frequency: 297.00MHz. System clock frequency: 198.00MHz. DRAM0 dunit_cfg/delay0_ctrl (0xf34111ba/0x000a8888). DRAM1 dunit_cfg/delay0_ctrl (0xe34111ba/0x000a8998). Using UART port 1 as console. Board ID.: "Pirelli STB HY100" Chip Revision: 0x8634:0x82 .. Mismatched. Setting up H/W from XENV block at 0xac000000. Keeping to 0x00000203. Setting to 0x00000000. Setting to 0x00000100. Setting to 0xff28ca00. Setting to 0x0000c000. Setting to 0x0000009f. Setting to 0x00000000. Setting to 0x0d000a00.
Setting to 0x010e0008. Setting to 0x010e0008. Setting to 0x000003fc. Setting to 0x00110101. Setting to 0x000003f3. PB cs config: 0x000c10c0 (use 0x000c10c0) Enabled Devices: 0x00023efe BM/IDE PCIHost Ethernet IR FIP I2CM I2CS USB PCIDev1 PCIDev2 PCIDev3 PCIDev4 SCARD MAC: 00:1c:a2:a4:28:ea PCI IRQ routing: IDSEL 1: INTA(#14) INTB(#14) INTC(#14) INTD(#14) IDSEL 2: INTA(#14) INTB(#14) INTC(#14) INTD(#14) IDSEL 3: INTA(#14) INTB(#14) INTC(#14) INTD(#14) IDSEL 4: INTA(#15) INTB(#15) INTC(#15) INTD(#15) Smartcard pin assignments: OFF pin = 0 5V pin = 1 CMD pin = 2 Setting up Clean Divider 2 to 96000000Hz. Setting up Clean Divider 4 to 33333333Hz. GPIO dir/data = 0x00000000/0x00000000 UART0 GPIO mode/dir/data = 0x6e/0x00/0x00 UART1 GPIO mode/dir/data = 0x6e/0x00/0x00 XENV block processing completed. Found existing memcfg: DRAM0(0x08000000), DRAM1(0x04000000) Default boot index: 0 MIGRATE PROCEDURE NO MIGRATE. Scanning ROMFS image at 0xac280000 (0x48280000) .. Found. ROMFS found at
0xac280000, Volume name = YAMON_XRPC Found 1 file(s) to be processed in ROMFS. Processing xrpc_xload_yamon-normal_ES4_prod.bin (start: 0xac2800a0, size: 0x00039414) Checking zboot file signature .. Not found. Trying xrpc_xload format .. OK Checking zboot file signature at 0x13000000 .. OK Warning: header version mismatched. Decompressing to 0x91160000 .. OK (527568/0x80cd0). Load time total 350 msec. Execute at 0x91160000 .. stand_by 0x0 i 0x1e DISPLAY SPLASHES ROMFS found at 0xac180000, Volume name = SPLASH_TEST Trovati 7 files da processare in ROM-FS Processing 11xrpc_xload_video_ucode_SMP8634_2.7.172.1_facsprod.mips.nodts.bin (start: 0xac182070, size: 0x0004e9d4) Checking zboot file signature .. Not found. Trying xrpc_xload format at 0xb3800000 .. Failed (not an xrpc_xload file) Processing 12xrpc_xload_demux_ucode_SMP8634_2.7.172.1_facsprod.mips.nodts.bin (start: 0xac206850, size: 0x00007954) Checking zboot file signature .. Not found. Trying xrpc_xload format at
0xb3800000 .. Failed (not an xrpc_xload file) Processing 30vsyncparam.zbf (start: 0xac1d0ae0, size: 0x00001aab) Checking zboot file signature .. OK. Warning: header version mismatched (0x02010000 instead expected 0x02000000). Decompressing 0xac1d0b00 to 0x10001000 .. Output length: 0x00007dc0(32192) OK (32192/0x7dc0). Processing 31bitmap.zbf (start: 0xac180080, size: 0x00001f84) Checking zboot file signature .. OK. Warning: header version mismatched (0x02010000 instead expected 0x02000000). Decompressing 0xac1800a0 to 0x17cacdc4 .. Output length: 0x0015223c(1385020) OK (1385020/0x15223c). Processing 32xrpc_xload_dviinit_ES4_prod.bin (start: 0xac2042b0, size: 0x00002534) Checking zboot file signature .. Not found. Trying xrpc_xload format at 0xb3800000 .. OK Checking zboot file signature at 0x13000000 .. OK Warning: header version mismatched (0x02010000 instead expected 0x02000000). Decompressing 0xb3000020 to 0xb0400000 .. Output length: 0x000046e0(18144) OK (18144/0x46e0).
Execute at 0xb0400000 .. Processing 33xrpc_xload_irq_handler_SMP8634_2.7.172.1_facsprod.mips.nodts.bin (start: 0xac1d25f0, size: 0x00031c74) Checking zboot file signature .. Not found. Trying xrpc_xload format at 0xb3800000 .. Failed (not an xrpc_xload file) Processing dvi.bin (start: 0xac1d0a70, size: 0x00000040) Checking zboot file signature .. Not found. Trying xrpc_xload format at 0xb3800000 .. Failed (not an xrpc_xload file) File 31bitmap.zbf found ~~~~~~ hdr=0xac180060 load_addr = 0x17cacdc4 ~~~~~~ inizio bitmap = 0xb7cad3fc, romfs_addr 0xac180000 A valid bitmap has been found: init the scart controller selected scart OUT to display splash screen ********************************** * YAMON ROM Monitor * Revision 02.06-SD-01-2.7.112.1-PIRELLI-20080619 ********************************** Memory: code: 0x11000000-0x11040000, 0x11160000-0x11164000 reserved data: 0x111a0000-0x123a0000, PCI memory: 0x123a0000-0x127a0000 Environment variable 'start' exists. After 10 seconds it
will be interpreted as a YAMON command and executed. Press Ctrl-C (or do BREAK) to bypass this. YAMON> fread tftp://192.168.1.1/vmliu nux.bin 0x90020000 Please initialize net first: net init | initpci YAMON> net init Ethernet driver for EM86XX (v1.0) (MAC 00:1c:a2:a4:28:ea, tx_desc/rx_desc = 16/32) em86xx_eth::open(em86xx_eth) - Full-duplex mode em86xx_eth::open(em86xx_eth) - 100 Mbit/s em86xx_eth ethernet start ipaddr: 192.168.1.2 subnetmask: 255.255.255.0 gateway: 192.168.0.254 YAMON> fread tftp://192.168.1.1/vmlinux.bin 0x90020000 About to binary read tftp://192.168.1.1/vmlinux.bin Successfully transferred 0x551085 (10'5574789) bytes YAMON> go 0x90020000 em86xx_eth ethernet stop [ 0.000000] Linux version 2.6.29.4-13-the_ripper (francesco@Spartan) (gcc version 4.4.3 (GCC) ) #1 PREEMPT Mon Nov 28 01:12:22 CET 2011 <4>[ 0.000000] Configured for SMP863x (revision ES6+/RevA+), detected SMP8634 (revision ES7/RevB). <4>[ 0.000000] Detected CPU/System/DSP Frequencies:
297.00/198.00/297.00MHz <6>[ 0.000000] console [prom0] enabled [ 0.000000] Configured for SMP863x (revision ES6+/RevA+), detected SMP8634 (revision ES7/RevB). <4>[ 0.000000] Detected CPU/System/DSP Frequencies: 297.00/198.00/297.00MHz <6>[ 0.000000] console [prom0] enabled [ 0.000000] Detected CPU/System/DSP Frequencies: 297.00/198.00/297.00MHz <6>[ 0.000000] console [prom0] enabled [ 0.000000] console [prom0] enabled [ 0.000000] prom console registered [ 0.000000] SMP86xx Enabled Devices under Linux/XENV 0x48000000 = 0x00023efe [ 0.000000] BM/IDE PCIHost Ethernet IR FIP I2CM I2CS USB PCIDev1 PCIDev2 PCIDev3 PCIDev4 SCARD [ 0.000000] Valid MEMCFG found at 0x10000fc0. [ 0.000000] CPU revision is: 00019068 (MIPS 4KEc) [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 06be0000 @ 10020000 (usable) [ 0.000000] Valid MEMCFG found at 0x10000fc0. [ 0.000000] User-defined physical RAM map: [ 0.000000] memory: 06be0000 @ 10020000 (usable) [ 0.000000] Wasting 2098176 bytes
for tracking 65568 unused pages [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00010020 -> 0x00016c00 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0x00010020 -> 0x00016c00 [ 0.000000] On node 0 totalpages: 27616 [ 0.000000] free_area_init_node: node 0, pgdat 90543780, node_mem_map 9059e400 [ 0.000000] Normal zone: 216 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 27400 pages, LIFO batch:7 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 27400 [ 0.000000] Kernel command line: console=ttyS0 root=/dev/sda1 rw rootdelay=20 mem=108m [ 0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes. [ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes) [ 0.000000] console handover:
boot [prom0] -> real [ttyS0] [ 0.001000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.003000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.028000] Memory: 103736k/110464k available (4333k kernel code, 6580k reserved, 940k data, 172k init, 0k highmem) [ 0.029000] Calibrating delay loop... 293.88 BogoMIPS (lpj=146944) [ 0.050000] Mount-cache hash table entries: 512 [ 0.068000] net_namespace: 700 bytes [ 0.070000] NET: Registered protocol family 16 [ 0.078000] tangox: creating TLB mapping for 0x20000000 at 0xc0000000, size 0x04000000. [ 0.079000] PCI: Initializing SMP8xxx PCI host controller [ 0.081000] PCI: Remapped PCI I/O space 0x58000000 to 0xc4020000, size 64 kB [ 0.082000] PCI: Remapped PCI config space 0x50000000 to 0xc4004000, size 10 kB [ 0.083000] PCI: Configured SMP8xxx as PCI slave with 128MB PCI memory [ 0.084000] PCI: Region size is 16384KB [ 0.085000] PCI: Map DMA memory 0x10020000-0x16c00000 for PCI at 0x11000000 [
0.145000] bio: create slab at 0 [ 0.151000] SCSI subsystem initialized [ 0.154000] usbcore: registered new interface driver usbfs [ 0.156000] usbcore: registered new interface driver hub [ 0.158000] usbcore: registered new device driver usb [ 0.171000] NET: Registered protocol family 2 [ 0.176000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.186000] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.194000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.201000] TCP: Hash tables configured (established 4096 bind 4096) [ 0.208000] TCP reno registered [ 0.211000] NET: Registered protocol family 1 [ 0.217000] timer0: interrupt registered. [ 0.222000] Created /proc/cpucache_info entry. [ 0.234000] NTFS driver 2.1.29 [Flags: R/W]. [ 0.239000] JFFS2 version 2.2. © 2001-2006 Red Hat, Inc. [ 0.245000] fuse init (API version 7.11) [ 0.251000] JFS: nTxBlock = 811, nTxLock = 6492 [ 0.258000] SGI XFS with security attributes, large
block/inode numbers, no debug enabled [ 0.269000] msgmni has been set to 202 [ 0.278000] alg: No test for stdrng (krng) [ 0.283000] io scheduler noop registered [ 0.287000] io scheduler anticipatory registered [ 0.292000] io scheduler deadline registered [ 0.296000] io scheduler cfq registered (default) [ 0.903000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.910000] serial8250: ttyS0 at MMIO 0x0 (irq = 10) is a 16550A [ 0.918000] serial8250: ttyS1 at MMIO 0x0 (irq = 9) is a 16550A [ 0.942000] loop: module loaded [ 0.946000] tango2_enet: ethernet driver for SMP863x internal mac [ 0.952000] tango2_enet: detected phy at address 0x01 [ 0.961000] tango2_enet: mac address 00:1c:a2:a4:28:ea [ 0.967000] Uniform Multi-Platform E-IDE driver [ 0.973000] ide-gd driver 1.18 [ 0.977000] ide-cd driver 5.00 [ 0.982000] TANGO2 Bus Mastering IDE interface (base 0xa00223c0,ctl 0xa0022398,irq 26) [ 0.991000] Probing IDE interface ide0... [ 1.514000] ide0 at
0x223c0-0x223dc,0x22398 on irq 26 [ 1.521000] Driver 'sd' needs updating - please use bus_type methods [ 1.529000] Driver 'sr' needs updating - please use bus_type methods [ 1.540000] physmap flash device CS2: 0x4000000 at 0x48000000 [ 1.548000] CS2: Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank [ 1.556000] Amd/Fujitsu Extended Query Table at 0x0040 [ 1.562000] CS2: Physically mapped flash: CFI does not contain boot bank location. Assuming top. [ 1.571000] number of CFI chips: 1 [ 1.575000] cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. [ 1.583000] ftl_cs: FTL header not found. [ 1.592000] Using physmap partition definition [ 1.596000] Adding partition #1-#9 [ 1.600000] Creating 9 MTD partitions on "CS2: Physically mapped flash": [ 1.607000] 0x000000000000-0x000000020000 : "CS2-Part1" [ 1.613000] ftl_cs: FTL header not found. [ 1.620000] 0x000000020000-0x000000120000 : "CS2-Part2" [ 1.626000] ftl_cs: FTL header not found. [
1.634000] 0x000000120000-0x000000140000 : "CS2-Part3" [ 1.640000] ftl_cs: FTL header not found. [ 1.648000] 0x000000140000-0x000000180000 : "CS2-Part4" [ 1.653000] ftl_cs: FTL header not found. [ 1.661000] 0x000000180000-0x000000280000 : "CS2-Part5" [ 1.667000] ftl_cs: FTL header not found. [ 1.675000] 0x000000280000-0x0000002c0000 : "CS2-Part6" [ 1.680000] ftl_cs: FTL header not found. [ 1.688000] 0x0000002c0000-0x0000004c0000 : "CS2-Part7" [ 1.694000] ftl_cs: FTL header not found. [ 1.702000] 0x0000004c0000-0x0000006c0000 : "CS2-Part8" [ 1.708000] ftl_cs: FTL header not found. [ 1.716000] 0x0000006c0000-0x000004000000 : "CS2-Part9" [ 1.721000] ftl_cs: FTL header not found. [ 1.729000] physmap flash device CS3: 0x4000000 at 0x4c000000 [ 1.739000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.746000] ehci_hcd: block sizes: qh 128 qtd 96 itd 160 sitd 96 [ 1.754000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.760000] ohci_hcd: block sizes: ed 64
td 64 [ 1.766000] tangox-ehci-hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.773000] Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after [ 1.782000] tangox-ehci-hcd: block sizes: qh 128 qtd 96 itd 160 sitd 96 [ 1.792000] TangoX USB initializing... [ 1.820000] tangox-ehci-hcd tangox-ehci-hcd: TangoX USB 2.0 [ 1.826000] drivers/usb/core/inode.c: creating file 'devices' [ 1.833000] drivers/usb/core/inode.c: creating file '001' [ 1.838000] tangox-ehci-hcd tangox-ehci-hcd: new USB bus registered, assigned bus number 1 [ 1.847000] tangox-ehci-hcd tangox-ehci-hcd: reset hcs_params 0x1212 dbg=0 cc=1 pcc=2 ordered ports=2 [ 1.857000] tangox-ehci-hcd tangox-ehci-hcd: reset hcc_params a026 thresh 2 uframes 256/512/1024 park [ 1.867000] tangox-ehci-hcd tangox-ehci-hcd: park 0 [ 1.872000] tangox-ehci-hcd tangox-ehci-hcd: irq 48, io mem 0xa0021400 [ 1.879000] tangox-ehci-hcd tangox-ehci-hcd: reset command 080b02 park=3 ithresh=8 period=1024 Reset
HALT [ 1.889000] tangox-ehci-hcd tangox-ehci-hcd: init command 010009 (park)=0 ithresh=1 period=256 RUN [ 1.904000] tangox-ehci-hcd tangox-ehci-hcd: USB 0.0 started, EHCI 1.00 [ 1.911000] usb usb1: default language 0x0409 [ 1.915000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.923000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.930000] usb usb1: Product: TangoX USB 2.0 [ 1.935000] usb usb1: Manufacturer: Linux 2.6.29.4-13-the_ripper tangox-ehci-hcd [ 1.943000] usb usb1: SerialNumber: tangox-ehci-hcd [ 1.948000] usb usb1: uevent [ 1.952000] usb usb1: usb_probe_device [ 1.956000] usb usb1: configuration #1 chosen from 1 choice [ 1.962000] usb usb1: adding 1-0:1.0 (config #1, interface 0) [ 1.969000] usb 1-0:1.0: uevent [ 1.973000] hub 1-0:1.0: usb_probe_interface [ 1.977000] hub 1-0:1.0: usb_probe_interface - got id [ 1.983000] hub 1-0:1.0: USB hub found [ 1.987000] hub 1-0:1.0: 2 ports detected [ 1.991000] hub 1-0:1.0:
standalone hub [ 1.995000] hub 1-0:1.0: individual port power switching [ 2.001000] hub 1-0:1.0: individual port over-current protection [ 2.007000] hub 1-0:1.0: power on to power good time: 20ms [ 2.013000] hub 1-0:1.0: local power source is good [ 2.018000] hub 1-0:1.0: enabling power on all ports [ 2.026000] drivers/usb/core/inode.c: creating file '001' [ 2.035000] tangox-ohci-hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.042000] tangox-ohci-hcd: block sizes: ed 64 td 64 [ 2.048000] TangoX USB was initialized. [ 2.052000] Initializing TangoX USB OHCI Controller Polling mode, Membase=0xa0021500 Status=0x0 [ 2.061000] hcd->register=0xa0021500 [ 2.065000] tangox-ohci-hcd tangox-ohci-hcd: USB Host Controller [ 2.072000] drivers/usb/core/inode.c: creating file '002' [ 2.078000] tangox-ohci-hcd tangox-ohci-hcd: new USB bus registered, assigned bus number 2 [ 2.087000] tangox-ohci-hcd tangox-ohci-hcd: io mem 0xa0021500 [ 2.093000] tangox-ohci-hcd tangox-ohci-hcd: created
debug files [ 2.123000] tangox-ehci-hcd tangox-ehci-hcd: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT [ 2.132000] hub 1-0:1.0: port 1: status 0501 change 0001 [ 2.214000] tangox-ohci-hcd tangox-ohci-hcd: OHCI controller state [ 2.220000] tangox-ohci-hcd tangox-ohci-hcd: OHCI 1.0, NO legacy support registers [ 2.228000] tangox-ohci-hcd tangox-ohci-hcd: control 0x083 HCFS=operational CBSR=3 [ 2.236000] tangox-ohci-hcd tangox-ohci-hcd: cmdstatus 0x00000 SOC=0 [ 2.243000] tangox-ohci-hcd tangox-ohci-hcd: intrstatus 0x00000044 RHSC SF [ 2.250000] tangox-ohci-hcd tangox-ohci-hcd: intrenable 0x8000005a MIE RHSC UE RD WDH [ 2.258000] tangox-ohci-hcd tangox-ohci-hcd: hcca frame #006d [ 2.264000] tangox-ohci-hcd tangox-ohci-hcd: roothub.a 20000202 POTPGT=32 NPS NDP=2(2) [ 2.273000] tangox-ohci-hcd tangox-ohci-hcd: roothub.b 00000000 PPCM=0000 DR=0000 [ 2.281000] tangox-ohci-hcd tangox-ohci-hcd: roothub.status 00008000 DRWE [ 2.288000] tangox-ohci-hcd tangox-ohci-hcd:
roothub.portstatus [0] 0x00000100 PPS [ 2.296000] tangox-ohci-hcd tangox-ohci-hcd: roothub.portstatus [1] 0x00000100 PPS [ 2.304000] usb usb2: default language 0x0409 [ 2.309000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.316000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.323000] usb usb2: Product: USB Host Controller [ 2.328000] usb usb2: Manufacturer: Linux 2.6.29.4-13-the_ripper tangox-ohci-hcd [ 2.336000] usb usb2: SerialNumber: TANGOX OHCI [ 2.342000] usb usb2: uevent [ 2.345000] hub 1-0:1.0: state 7 ports 2 chg 0002 evt 0000 [ 2.351000] hub 1-0:1.0: port 1, status 0501, change 0000, 480 Mb/s [ 2.358000] usb usb2: usb_probe_device [ 2.362000] usb usb2: configuration #1 chosen from 1 choice [ 2.368000] usb usb2: adding 2-0:1.0 (config #1, interface 0) [ 2.375000] usb 2-0:1.0: uevent [ 2.379000] hub 2-0:1.0: usb_probe_interface [ 2.383000] hub 2-0:1.0: usb_probe_interface - got id [ 2.389000] hub 2-0:1.0: USB hub found [
2.393000] hub 2-0:1.0: 2 ports detected [ 2.397000] hub 2-0:1.0: standalone hub [ 2.401000] hub 2-0:1.0: no power switching (usb 1.0) [ 2.407000] hub 2-0:1.0: global over-current protection [ 2.412000] hub 2-0:1.0: power on to power good time: 64ms [ 2.418000] hub 2-0:1.0: local power source is good [ 2.423000] hub 2-0:1.0: no over-current condition exists [ 2.429000] hub 2-0:1.0: trying to enable port power on non-switchable hub [ 2.437000] tangox-ehci-hcd tangox-ehci-hcd: port 1 high speed [ 2.437000] tangox-ehci-hcd tangox-ehci-hcd: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT [ 2.454000] drivers/usb/core/inode.c: creating file '001' [ 2.462000] Initializing USB Mass Storage driver... [ 2.468000] usbcore: registered new interface driver usb-storage [ 2.475000] USB Mass Storage support registered. [ 2.482000] usbcore: registered new interface driver usbhid [ 2.488000] usbhid: v2.6:USB HID core driver [ 2.495000] TCP cubic registered [ 2.499000] NET: Registered
protocol family 17 [ 2.504000] usb 1-1: new high speed USB device using tangox-ehci-hcd and address 2 [ 2.513000] RPC: Registered udp transport module. [ 2.518000] RPC: Registered tcp transport module. [ 2.528000] Waiting 20sec before mounting root device... [ 2.575000] tangox-ehci-hcd tangox-ehci-hcd: port 1 high speed [ 2.575000] tangox-ehci-hcd tangox-ehci-hcd: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT [ 2.654000] usb 1-1: default language 0x0409 [ 2.659000] usb 1-1: New USB device found, idVendor=1307, idProduct=0165 [ 2.666000] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.674000] usb 1-1: Product: USB Flash Drive [ 2.678000] usb 1-1: Manufacturer: USB 2.0 [ 2.683000] usb 1-1: SerialNumber: 2c21e7f2d9d5d5 [ 2.688000] usb 1-1: uevent [ 2.692000] usb 1-1: usb_probe_device [ 2.696000] usb 1-1: configuration #1 chosen from 1 choice [ 2.702000] usb 1-1: adding 1-1:1.0 (config #1, interface 0) [ 2.709000] usb 1-1:1.0: uevent [ 2.713000]
usb-storage 1-1:1.0: usb_probe_interface [ 2.718000] usb-storage 1-1:1.0: usb_probe_interface - got id [ 2.725000] scsi0 : SCSI emulation for USB Mass Storage devices [ 2.736000] usb-storage: device found at 2 [ 2.740000] usb-storage: waiting for device to settle before scanning [ 2.750000] drivers/usb/core/inode.c: creating file '002' [ 2.758000] hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 3.751000] scsi 0:0:0:0: Direct-Access USB 2.0 USB Flash Drive 0.00 PQ: 0 ANSI: 2 [ 3.764000] sd 0:0:0:0: [sda] 7897088 512-byte hardware sectors: (4.04 GB/3.76 GiB) [ 3.773000] sd 0:0:0:0: [sda] Write Protect is off [ 3.778000] sd 0:0:0:0: [sda] Mode Sense: 00 00 00 00 [ 3.784000] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 3.795000] sd 0:0:0:0: [sda] 7897088 512-byte hardware sectors: (4.04 GB/3.76 GiB) [ 3.804000] sd 0:0:0:0: [sda] Write Protect is off [ 3.809000] sd 0:0:0:0: [sda] Mode Sense: 00 00 00 00 [ 3.815000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 3.821000] sda: sda1 sda2 [ 3.969000] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 3.977000] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 3.988000] usb-storage: device scan complete [ 22.543000] kjournald starting. Commit interval 5 seconds [ 22.550000] EXT3 FS on sda1, internal journal [ 22.555000] EXT3-fs: mounted filesystem with ordered data mode. [ 22.561000] VFS: Mounted root (ext3 filesystem) on device 8:1. [ 22.570000] Freeing unused kernel memory: 172k freed [ 23.026000] Please be patient, while OpenWrt loads ... [ 23.720000] usb usb1: uevent [ 23.724000] usb 1-0:1.0: uevent [ 23.729000] usb usb2: uevent [ 23.734000] usb 2-0:1.0: uevent [ 23.739000] usb 1-1: uevent [ 23.744000] usb 1-1:1.0: uevent - preinit - Press the [f] key and hit [enter] to enter failsafe mode - regular preinit - - init usb - - init - Please press Enter to activate this console. [ 34.820000] NET: Registered protocol family 10 [ 34.831000] lo: Disabled Privacy Extensions [ 37.046000]
Compat-wireless backport release: compat-wireless-2011-06-23 [ 37.064000] Backport based on wireless-testing.git master-2011-06-22 [ 37.763000] cfg80211: Calling CRDA to update world regulatory domain [ 38.387000] cfg80211: World regulatory domain updated: [ 38.435000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 38.469000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 38.515000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 38.545000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 38.578000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 38.601000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 39.919000] usbcore: registered new interface driver rt2800usb [ 40.542000] tun: Universal TUN/TAP device driver, 1.6 [ 40.548000] tun: (C) 1999-2004 Max Krasnyansky [ 40.754000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 41.250000] usbcore: registered new interface driver usbserial [ 41.257000] usbserial: USB Serial Driver core [ 41.346000] USB Serial support registered for FTDI USB Serial Device [ 41.357000] usbcore: registered new interface driver ftdi_sio [ 41.363000] ftdi_sio: v1.4.3:USB FTDI Serial Converters Driver [ 41.437000] USB Serial support registered for pl2303 [ 41.446000] usbcore: registered new interface driver pl2303 [ 41.453000] pl2303: Prolific PL2303 USB to serial adaptor driver [ 41.465000] usb 1-0:1.0: uevent [ 41.495000] usb 1-1: uevent [ 41.503000] usb 1-1:1.0: uevent [ 41.513000] usb 2-0:1.0: uevent [ 41.519000] usb usb1: uevent [ 41.529000] usb usb2: uevent [ 42.086000] ramzswap: num_devices not specified. Using default: 1 [ 42.109000] ramzswap: /dev/ramzswap0 initialized: disksize_kb=16384<6>Adding 16376k swap on /dev/ramzswap0. Priority:-1 extents:1 across:16376k SS BusyBox v1.18.5 (2011-11-27 20:28:56 CET) built-in shell (ash) Enter 'help' for a list of built-in
commands. _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ATTITUDE ADJUSTMENT (bleeding edge, r27943) ---------- * 1/4 oz Vodka Pour all ingredients into mixing * 1/4 oz Gin tin with ice, strain into glass. * 1/4 oz Amaretto * 1/4 oz Triple sec * 1/4 oz Peach schnapps * 1/4 oz Sour mix * 1 splash Cranberry juice ----------------------------------------------------- root@(none):/# lsmod Module Size Used by Not tainted ramzswap 19392 1 lzo1x 4080 1 ramzswap pl2303 19840 0 ftdi_sio 51392 0 usbserial 31872 2 pl2303,ftdi_sio ipt_REJECT 3216 0 xt_TCPMSS 3200 0 ipt_LOG 6640 0 xt_comment 944 0 xt_multiport 2528 0 xt_mac 1056 0 xt_limit 1872 0 iptable_mangle 1840 0 iptable_filter 1792 0 ip_tables 10656 2 iptable_mangle,iptable_filter xt_tcpudp 2544 0 x_tables 13936 9 ipt_REJECT,xt_TCPMSS,ipt_LOG,xt_comment,xt_multiport,xt_mac,xt_limit,ip_tables,xt_tcpudp tun
11808 0 ext4 245408 0 jbd2 63872 1 ext4 cifs 304016 0 rt2800usb 23056 0 rt2800lib 45120 1 rt2800usb rt2x00usb 11040 1 rt2800usb rt2x00lib 41792 3 rt2800usb,rt2800lib,rt2x00usb mac80211 301664 3 rt2800lib,rt2x00usb,rt2x00lib crc_ccitt 1312 1 rt2800lib cfg80211 173920 2 rt2x00lib,mac80211 compat 24544 3 rt2x00lib,mac80211,cfg80211 arc4 1248 0 aes_generic 30640 0 ipv6 322848 10 root@(none):/# uname -a Linux (none) 2.6.29.4-13-the_ripper #1 PREEMPT Mon Nov 28 01:12:22 CET 2011 mips GNU/Linux root@(none):/# iwcoroot@(none):/# iwconfig lo no wireless extensions. eth0 no wireless extensions. root@(none):/# [ 112.461000] hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0004 [ 112.468000] tangox-ehci-hcd tangox-ehci-hcd: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT [ 112.478000] hub 1-0:1.0: port 2, status 0501, change 0001, 480 Mb/s [ 112.589000] hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501 [ 112.648000] tangox-ehci-hcd tangox-ehci-hcd: port 2 high speed [
112.648000] tangox-ehci-hcd tangox-ehci-hcd: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT [ 112.715000] usb 1-2: new high speed USB device using tangox-ehci-hcd and address 3 [ 112.777000] tangox-ehci-hcd tangox-ehci-hcd: port 2 high speed [ 112.777000] tangox-ehci-hcd tangox-ehci-hcd: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT [ 112.867000] usb 1-2: default language 0x0409 [ 112.879000] usb 1-2: New USB device found, idVendor=148f, idProduct=2070 [ 112.887000] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 112.895000] usb 1-2: Product: 802.11 g WLAN [ 112.900000] usb 1-2: Manufacturer: Ralink [ 112.905000] usb 1-2: SerialNumber: 1.0 [ 112.911000] usb 1-2: uevent [ 112.923000] usb 1-2: usb_probe_device [ 112.927000] usb 1-2: configuration #1 chosen from 1 choice [ 112.955000] usb 1-2: adding 1-2:1.0 (config #1, interface 0) [ 112.967000] usb 1-2:1.0: uevent [ 112.975000] rt2800usb 1-2:1.0: usb_probe_interface [ 112.983000]
rt2800usb 1-2:1.0: usb_probe_interface - got id [ 113.049000] tangox-ehci-hcd tangox-ehci-hcd: port 2 high speed [ 113.049000] tangox-ehci-hcd tangox-ehci-hcd: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT [ 113.117000] usb 1-2: reset high speed USB device using tangox-ehci-hcd and address 3 [ 113.179000] tangox-ehci-hcd tangox-ehci-hcd: port 2 high speed [ 113.179000] tangox-ehci-hcd tangox-ehci-hcd: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT [ 113.338000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 113.384000] Registered led device: rt2800usb-phy0::radio [ 113.394000] Registered led device: rt2800usb-phy0::assoc [ 113.407000] Registered led device: rt2800usb-phy0::quality [ 113.423000] drivers/usb/core/inode.c: creating file '003' root@(none):/# cat /prroot@(none):/# cat /proc/busroot@(none):/# cat /proc/bus/usroot@(none):/# cat /proc/bus/usb/deviroot@(none):/# cat /proc/bus/usb/devices T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=
1 Spd=12 MxCh= 2 B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0001 Rev= 2.06 S: Manufacturer=Linux 2.6.29.4-13-the_ripper tangox-ohci-hcd S: Product=USB Host Controller S: SerialNumber=TANGOX OHCI C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 2 B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0002 Rev= 2.06 S: Manufacturer=Linux 2.6.29.4-13-the_ripper tangox-ehci-hcd S: Product=TangoX USB 2.0 S: SerialNumber=tangox-ehci-hcd C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00
Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1307 ProdID=0165 Rev= 1.00 S: Manufacturer=USB 2.0 S: Product=USB Flash Drive S: SerialNumber=2c21e7f2d9d5d5 C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr= 98mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=16ms T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=148f ProdID=2070 Rev= 1.01 S: Manufacturer=Ralink S: Product=802.11 g WLAN S: SerialNumber=1.0 C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=450mA I:* If#= 0 Alt= 0 #EPs= 7 Cls=ff(vend.) Sub=ff Prot=ff Driver=rt2800usb E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E:
Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms root@(none):/# iwcoroot@(none):/# iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm RTS thr:off Fragment thr:off Encryption key:off Power Management:on root@(none):/# iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan0 Interface doesn't support scanning : Network is down root@(none):/# ifconfig wlan0 up [ 188.044000] ADDRCONF(NETDEV_UP): wlan0: link is not ready root@(none):/# iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan0 Scan completed : Cell 01 - Address: 38:22:9D:37:D8:B8 Channel:1 Frequency:2.412 GHz (Channel 1) Quality=33/70 Signal level=-77 dBm Encryption key:on ESSID:"Alice-31238231" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s Mode:Master
Extra:tsf=000000e244f8a573 Extra: Last beacon: 1401ms ago IE: Unknown: 000E416C6963652D3331323338323331 IE: Unknown: 010882848B962430486C IE: Unknown: 030101 IE: Unknown: 2A0100 IE: Unknown: 2F0100 IE: Unknown: 32040C121860 IE: Unknown: DD600050F204104A00011010440001021041000100103B0001031047001000000000000000000000000000000000102100001023000010240000104200001054000800000000000000001011000E416C6963652D3331323338323331100800020000 IE: Unknown: DD090010180200F0000000 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK Cell 02 - Address: 00:1D:8B:41:FF:74 Channel:11 Frequency:2.462 GHz (Channel 11) Quality=41/70 Signal level=-69 dBm Encryption key:on ESSID:"JackTheVendicator" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s Mode:Master Extra:tsf=00000161926c7d0b Extra: Last beacon: 559ms ago IE: Unknown: 00114A61636B54686556656E64696361746F72 IE: Unknown:
010882848B962430486C IE: Unknown: 03010B IE: Unknown: 2A0107 IE: Unknown: 2F0107 IE: Unknown: 32040C121860 IE: Unknown: DD060010180200F4 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK root@(none):/# iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination root@(none):/# ls /etroot@(none):/# ls /etc/coroot@(none):/# ls /etc/config/ autofs compcache network ntpclient system timeserver root@(none):/# opkg list_installed alsa-lib - 1.0.24.1-1 autofs4 - 4.1.4-1 azbox-showiframe - 1 base-files-generic - 78-r27943 blkid - 1.41.12-2 busybox - 1.18.5-1 bzip2 - 1.0.6-1 cfdisk - 2.13.0.1-4 compcache - 0.6.2-2 crda - 1.1.1-1 e2fsprogs - 1.41.12-2 event_test - 0.01-1 evexec - 1.0-1 evtest - 20100422-1 fdisk - 2.13.0.1-4 fontconfig - 2.6.0-2 glibc-gconv - 2.10.2-78 glibc-gconv-iso8859-15 -
2.10.2-78 glibc-gconv-iso8859-9 - 2.10.2-78 glibc-gconv-utf-32 - 2.10.2-78 hotplug2 - 1.0-beta-4 iptables - 1.4.10-3 iw - 0.9.22-2 kernel - 2.6.29.4-1 kmod-cfg80211 - 2.6.29.4+2011-06-22-2 kmod-crc-ccitt - 2.6.29.4-1 kmod-crypto-aes - 2.6.29.4-1 kmod-crypto-arc4 - 2.6.29.4-1 kmod-fs-cifs - 2.6.29.4-1 kmod-fs-ext4 - 2.6.29.4-1 kmod-fuse - 2.6.29.4-1 kmod-ipt-core - 2.6.29.4-1 kmod-ipv6 - 2.6.29.4-1 kmod-mac80211 - 2.6.29.4+2011-06-22-2 kmod-ramzswap - 2.6.29.4-azbox-1+2 kmod-rt2800-lib - 2.6.29.4+2011-06-22-2 kmod-rt2800-usb - 2.6.29.4+2011-06-22-2 kmod-rt2x00-lib - 2.6.29.4+2011-06-22-2 kmod-rt2x00-usb - 2.6.29.4+2011-06-22-2 kmod-sc - 2.6.29.4-1 kmod-tun - 2.6.29.4-1 kmod-usb-serial - 2.6.29.4-1 kmod-usb-serial-ftdi - 2.6.29.4-1 kmod-usb-serial-pl2303 - 2.6.29.4-1 libblkid - 1.41.12-2 libbsd - 0.3.0-1 libbz2 - 1.0.6-1 libc - 2.10.2-78 libcom_err - 1.41.12-2 libexpat - 2.0.1-1 libext2fs - 1.41.12-2 libfreetype - 2.3.12-1 libfuse - 2.8.5-1 libgcc - 4.4.3+ab-78 libip4tc -
1.4.10-3 libjpeg - 6b-1 libncurses - 5.7-5 libnl-tiny - 0.1-2 libopenssl - 1.0.0d-1 libpng - 1.2.44-1 libpthread - 2.10.2-78 librt - 2.10.2-78 libstdcpp - 4.4.3+ab-78 libuci - 2011-07-18.3-1 libuuid - 1.41.12-2 libwrap - 7.6-1 libxtables - 1.4.10-3 mtd - 16 ntfs-3g - 2011.4.12-1-fuseint ntpclient - 2007_365-4 opkg - 618-1 portmap - 6.0-2 sfdisk - 2.13.0.1-4 strace - 4.5.20-1 swap-utils - 2.13.0.1-4 terminfo - 5.7-5 tune2fs - 1.41.12-2 tzdata-europe - 2008e-1 uci - 2011-07-18.3-1 vsftpd - 2.3.4-2 wireless-tools - 29-4 wpad-mini - 20110527-1 zlib - 1.2.5-1 root@(none):/# shutdown /bin/ash: shutdown: not found root@(none):/# halt root@(none):/# root@(none):/# [ 298.215000] System halted.{/syntaxhighlighter}
My wishlistDonate

Avatar utente
estebanSannin
Messaggi: 524
Iscritto il: sabato 22 gennaio 2011, 13:02
Località: Milano
Contatta:

OpenWrt su Pirelli STB

Messaggioda estebanSannin » lunedì 28 novembre 2011, 19:34

bhe direi Ottimo lavoro Jack!!

Presto riavro' tra le mie mani il mio vecchio STB e inizieremo a sviluppare una bella versione di OpenWRT ;-)
HackLabProject Founder
DroniX Founder
Immagine
Personal site: http://esteban.homelinux.org

VanniX
Messaggi: 454
Iscritto il: mercoledì 16 febbraio 2011, 20:17

Re: OpenWrt su Pirelli STB

Messaggioda VanniX » lunedì 28 novembre 2011, 23:08

Io ho l'STB, e il progetto di usarlo in casa come decoder è gia decaduto.. Causa brick ripetuti..

Quindi, se ho tempo, sono a disposizione per i test e per qualche aiuto (a patto che siano robe estremamente semplici che so fare anche io).

JackTheVendicator
Messaggi: 43
Iscritto il: sabato 22 gennaio 2011, 22:56

Re: OpenWrt su Pirelli STB

Messaggioda JackTheVendicator » mercoledì 30 novembre 2011, 11:37

L'installazione e' molto semplice... si tratta del solito flash kernel via YAMON + rootfs su penna USB. Devo ancora rifinire alcune cose (in particolare far fuori le parti specifiche azbox, visto che voglio ottenere un openwrt "puro"), e poi potro' pubblicare una beta Laughing
My wishlistDonate

VanniX
Messaggi: 454
Iscritto il: mercoledì 16 febbraio 2011, 20:17

Aspetto fiducioso :)

Messaggioda VanniX » mercoledì 30 novembre 2011, 21:43

Aspetto fiducioso :)

mormoros
Messaggi: 1
Iscritto il: domenica 4 dicembre 2011, 23:23

credo di averne uno in piu da

Messaggioda mormoros » domenica 4 dicembre 2011, 23:33

credo di averne uno in piu da poter sacafricare.

JackTheVendicator
Messaggi: 43
Iscritto il: sabato 22 gennaio 2011, 22:56

Purtroppo ho posticipato il

Messaggioda JackTheVendicator » venerdì 9 dicembre 2011, 19:33

Purtroppo ho posticipato il progetto per un tempo indefinito a causa di problemi con la compilazione dei moduli crypto
My wishlistDonate


Torna a “STB Pirelli”

Chi c’è in linea

Visitano il forum: Nessuno e 1 ospite